Skip to content
MT5MT4soonTradingViewsooncTradersoonNinjaTradersoonPythonsoon
MetaTrader & platform basics

Multi-timeframe

Also called MTF, Multi-timeframe analysis, Multiple timeframe analysis, Multi timeframe trading, Top-down analysis

Multi-timeframe trading means reading the same market on two or three chart timeframes before a trade: a higher one for direction, a middle one for the price area, and a lower one to time the entry and place the stop.

A setup that looks clean on a 1-hour chart can sit directly under a daily resistance level you never saw. Checking more than one timeframe is how you avoid that trade. It also changes how many pips your stop needs, and so your lot size.

Giving each timeframe one job

A multi-timeframe routine works when each chart answers a single question.

Keep the charts about four to six times apart. Closer than that and they show the same picture twice. Further apart and the lower chart's moves are too small to matter on the higher one.

StyleDirectionLocationTrigger
SwingWeeklyDaily4-hour
IntradayDaily4-hour1-hour
Short-term4-hour1-hour15-minute
Scalping1-hour15-minute3-minute

The drawing below shows one buy setup seen through the three charts of the intraday row.

One buy setup on the daily, 4-hour and 1-hour charts
Each yellow box is the area the next panel zooms into. The entry is where the 1-hour price breaks its last high.

The next section puts numbers on this same setup.

How the lower chart changes your lot size: a worked example

The figures here are an illustrative example. You have a $10,000 account and risk 1% per trade, so $100. On a USD-quoted pair, one standard lot is worth $10 per pip.

The daily chart trends up. The 4-hour chart pulls back to support. You buy at 1.1010 and aim for the daily high at 1.1110, which is 100 pips away.

You can place a stop at 1.0960, just under the 4-hour swing low (50 pips), or at 1.0990, just under the 1-hour swing low (20 pips).

1-hour chart of the 1.1010 buy with two stops: 1.0990 under the 1-hour swing low and 1.0960 under the 4-hour swing lowIllustration
Target: daily high 1.11101.1110Entry 1.10101.10101-hour stop 1.0990 (20 pips)1.09904-hour stop 1.0960 (50 pips)1.09604-hour swing low1-hour swing lowBuy
Both stops sit under a real swing low. The 1-hour stop is 20 pips away and the 4-hour stop is 50 pips away. The target at 1.1110 is the same for both.
Stop taken fromStop distanceLot size for $100 riskProfit at the targetReward per $1 risked
4-hour swing low50 pips0.20 lots$2002
1-hour swing low20 pips0.50 lots$5005

The steps below show the 1-hour version so you can redo it with your own numbers.

Lot size and reward with a stop taken from the 1-hour chart
Risk in money$10,000 × 1%= $100
Lots$100 ÷ (20 × $10)= 0.50
Profit at target100 × 0.50 × $10= $500
Reward for each $1 risked$500 ÷ $100= 5
Order size0.50 lots

The loss is $100 in both cases. The tighter stop gives a larger position toward the same target, but ordinary 1-hour noise reaches it more easily. A rule you can apply: if the 1-hour stop is smaller than a typical 1-hour candle's range, use the 4-hour stop and the smaller lot size. Multi-timeframe trading does not remove that trade-off. It lets you see it and choose.

Checks before you trade across timeframes

  • Go top-down. Start on the highest chart. If you start on the lowest, you will search the higher charts for agreement with a trade you already want.
  • Wait for the higher-timeframe close. A candle that is still forming can flip before it ends: a daily candle that looks bullish at midday may close bearish.
  • If the top two timeframes disagree, stand aside. If the higher one is flat, do not look for a trend trade.
  • Mark higher-timeframe levels first. Draw them on the higher chart before you drop down. If one sits between your entry and your target, your target is that level.
  • Fix your set of timeframes in advance. Adding a fourth chart mid-trade usually means you are looking for permission.

Reading a multi-timeframe indicator without being fooled

A multi-timeframe (MTF) indicator calculates on a higher timeframe and draws the result on your lower chart. A daily moving average on a 1-hour chart, for example, appears as a stepped line: one daily value is held flat across all the 1-hour bars of that day, then the line steps to the next day's value.

The last step is different. Its daily candle is still forming, so its value is recalculated as price moves and keeps changing until that candle closes. A signal that appears and then vanishes was read from this open step.

The rule: only act on steps that end at a completed higher-timeframe candle. With a daily MTF line on a 1-hour chart, that means trusting yesterday's step, not today's, until the daily candle closes.

The drawing below shows the same problem on a single daily candle: bullish at midday, bearish at the close.

A daily candle that looks bullish at midday but closes bearish
The candle is not finished until the close. Read signals from closed higher-timeframe candles only.

FAQ

Can I trade with only two timeframes?

Yes. Use the higher one for direction and levels, and the lower one for entry and stop. You lose the middle step, so mark your zones carefully on the higher chart before dropping down.

Does the same indicator setting mean the same thing on every timeframe?

No. A period counts candles, not time. A 50-period average covers 50 days on a daily chart and 50 hours on a 1-hour chart. To approximate the daily one on a 1-hour chart in a 24-hour market, multiply: 50 × 24 = 1,200 periods.

Hours of price covered by a 50-period average on the daily chart, a 50-period on the 1-hour chart and a 1,200-period on Illustration
50-period, daily chart
50 days = 1,200 hours
50-period, 1-hour chart
50 hours
1,200-period, 1-hour chart
1,200 hours = 50 days

Related terms